How To Use A Hat Press
Information technology's possible to put heat transfer vinyl on hats with a regular heat press, only a heat press makes information technology much, much easier (and safer!).
This is a sponsored post, but all opinions are my own. |
Today I thought I'd share a beginner hat heat printing tutorial with you and then you can see just how easy it is to estrus i.
Setting Up a Lid Press for the Outset Time
I accept the Trans Pro Semi-Auto Cap heat printing from Pro World. A link to the PDF manual is provided, merely it'southward kinda defective so allow me...
The commencement thing you desire to do is unpack your chapeau press and make sure to remove all packing materials and zippo ties. Prepare it upwardly on a solid surface and plug information technology in.
The power push button is on the right side with the controls on the top. The time and temperature will be determined by the type of heat transfer vinyl you lot are applying.
To set the temperature on this Trans Pro hat press, click the Ready button (gear) and wait for the P-one message. So click the upward and down arrows to set the temperature. (Siser Easyweed should exist pressed at 305 for fifteen-xx seconds.)
Once the temperature is fix, press the Ready button again to lock it in. Information technology should now say P-two. Again, press the up and downward arrows to set the fourth dimension.
Look for the press to come to temperature. The manufacture says this will take about 20 minutes, only I timed warming it up at least iii times and it was closer to 5-7 minutes.
Best Hats for Lid Estrus Printing
The easiest hats to use with a cap heat press are 5 panel hats rather than 6 console hats. Five panel caps do not take a seam down the front center of the chapeau making it easier to press onto the large front console.
Half dozen panel hats split the front end console of the cap into two sections putting a seam correct downward the middle - making it more challenging to press onto the cap. If yous are using a 6 panel hat, a thicker rut transfer material such as glitter heat transfer vinyl or Flock HTV ideal for pressing over the thick center seam.
You tin can press onto cotton or twill hats, polyester hats, and foam and mesh trucker-mode hats to proper name a few!
Cut HTV for Hats
Measure the front panel of the bare hat and and so make up one's mind how big you desire your blueprint to exist. Measure again...you don't want your design to exist besides big. Ask me how I know... For an adult hat, I think nigh 5-6" across is perfect.
In Silhouette Studio scale the design using the corner of the option box or past manually typing in the dimensions in the Calibration tool (found within the Transform panel on the right sidebar).
Applying HTV to Caps with a Hat Heat Press Machine
Cut the HTV with your Silhouette motorcar while the hat press warms up to the correct temperature.
If you demand a refresher on how to cut heat transfer vinyl, check out this beginner tutorial.
Place the HTV vinyl decal onto the hat before you put it onto the printing. To keep it in place, utilize some high estrus record (also available at Pro World).
To put the chapeau on the Trans Pro Semi Auto Cap heat press, start past looping the back of the lid around the metallic hat belongings device. And then stretch the hat onto the rounded heating board.
The beak of the hat should be pointing up.
Make certain the sweat band of the heat is flipped forward and then it'southward not calculation actress majority while pressing.
I actually skipped the teflon sheet, merely there'due south no impairment in using one while pressing.
Pull the handle down until it locks. The timer should start counting down.
When it reaches the stop of the pressing fourth dimension, the Trans Pro Semi Machine cap press will automatically release and lift the handle. I accept to say I love this feature!
Peel away the articulate carrier sheet from your heat transfer vinyl and you lot're done!
It really is that like shooting fish in a barrel!
If you want to add together HTV to the brim of the hat, flip the lid around and place the skirt on the heating board and use estrus and pressure.
If you're looking for an easy to utilise hat heat printing I would definitely recommend the Trans Pro Semi Automatic Cap press from Pro World. It'due south easy and fast to use and leaves you lot with a quality professional-looking custom hat!
Note: This post may contain chapter links. Past clicking on them and purchasing products through my links, I receive a minor committee. That'due south what helps fund Silhouette School so I tin keep ownership new Silhouette-related products to show yous how to get the almost out of your machine!
Get Silhouette School lessons delivered to your e-mail inbox! Select Once Daily or Weekly.
How To Use A Hat Press,
Source: https://www.silhouetteschoolblog.com/2017/09/hat-press-tutorial-silhouette-cameo-beginners.html
Posted by: simonsdecten.blogspot.com
0 Response to "How To Use A Hat Press"
Post a Comment